-
2GRahmen - eine frage
Antwort per Mail
-
Fachwerk
um ein Doppel-T-Profil in dem Fachwerkmakro zur Verfügung zu stellen, gehen Sie wie folgt vor:
- Öffnen Sie die Management Tools
- Klicken Sie dort auf den Tabelleneditor
- Klicken Sie dort oben links auf ODBC öffnen
- Klicken Sie nun auf den Pfeil rechts neben dem Eintrag "AstorRules"
- Suchen Sie nun die Tabelle "JointsGUIAllowedSections"
- in dieser Tabelle suchen Sie in der Spalte "JointName" die Einträge "SETruss
Hier gibt Einträge für die vier Bestandteile des Fachwerkes. Zu erkennen ist das in der Spalte "JointControl"
TopSection für den oberen Träger
Botton Section für den unteren Träger
DiagonalSection für die Diagonale
VerticalSection für den Pfosten
- Kopieren Sie nun jeweils eine dieser Zeilen und fügen Sie am Ende der Tabelle wieder mit einem neuen Key ein.
Damit Sie keinen doppelten Key verwenden, fangen Sie bei 22000 an.
- Ersetzen Sie nun den Eintrag in die vier neuen Zeilen in der Spalte "Allowed Section" durch ein großes i
Dieses steht für I-Profile oder Doppel-T-Profile
- Danach schließen Sie die Tabelle und die Management Tools wieder. Die Einträge werden automatisch gespeichert.
- Gehen Sie dann in Advance Steel zurück und klicken im Register "Basis" in der Gruppe "Einstellungen" auf die
Funktion "Voreinstellungen" aktualisieren".
- Nun müssten im Fachwerk die Doppel-T-Profile zur Verfügung stehen.
Übrigens: Das funktioniert mit jeder Profilart. Man muss nur die Kennzeichnung der Profilart kennen. Diese finden Sie in der Datenbank AstorProfiles in der Tabelle "ProfileMasterTable"
-
Baugruppenanstrich
Hallo Herr Baliu,
leider können wir das Problem nicht reproduzieren.
Um das Problem genauer untersuchen zu können, wäre es besser, wenn Sie sich direkt bei unserem Support (support.germany@graitec.com) melden.
Über das Forum ist das nicht machbar.
MfG
Elias Theuring
-
Unkontrollierbare Änderungen nach dem einfügen nachträglicher Schnitte
Hallo Herr Schwarzl,
mit welcher Advance Steel Version arbeiten Sie?
Bei den Bemaßungen kann das hin- und wieder vorkommen. Evtl. liegt das auch an Ihren Voreinstellungen.
Bei Verschieben von Positionsnummern müssen Sie darauf achten, dass Sie nicht den Schiebebefehl von AutoCAD verwenden, sondern die Beschriftungen anklicken und dann über den angezeigten Griffpunkt verschieben. Den Anfangspunkt der Führungslinie der Beschriftung dürfen Sie nicht von der Körperkante wegschieben.
Am besten schicken Sie uns dazu driekt eine E-Mail an support.germany@graitec.com
MfG
Elias Theuring
-
Hallo,<br/><br/>beim Starten des Management-Tools bricht es ab.<br/>Fehlermeldung liegt bei.<br/><br/>Vielen Dank für Ihre Hilfe.<br/><br/>Herbert Hornung<br/>Baubetreuung
Hallo Herr Hornung,
wie ich Ihnen bereits in einer Mail mitgeteilt habe, liegt hier wohl ein Problem bei Installation vor.
Noch eine Bitte in eigener Sache. Wenn Sie uns Supportanfragen stellen, stellen Sie diesen bitte nur auf einem Weg. Am besten schicken Sie gleich eine E-Mail.
Das Forum hier ist eher ein Mittel zur Selbsthilfe. User sollen sich gegenseitig helfen.
Supportanfragen über mehrere Wege zu schicken, macht keinen Sinn, da Sie alle an der gleichen Stelle landen. Sie verschaffen uns dadurch nur noch mehr Aufwand.
Vielen Dank für Ihr Verständnis.
MfG
Elias Theuring
-
Layoutbereich im Advance CAD
Hallo Herr Schwarzl,
in Advance CAD ist diese Funktionalität nicht implementiert. In AutoCAD ist dies ohne Probleme möglich.
Diese Funktionalität ist auf unserer Entwicklungswunschliste bereits enthalten.
MfG
Elias Theuring
-
Kann beim Advance Steel in der Maske nicht die Autocadversion 2014 (19.1) einstellen.<br/>Programm öffnet sich dann nicht.<br/>mit AutoCAD 2012 geht es. <br/>Bitte um RR, danke
Sehr geehrte Damen und Herren,
wenn Sie eine neue Version von Advance Steel, z.B. die Version 2014 installieren und diese zusammen mit AutoCAD verwenden, ist es meistens von Vorteil, wenn man dem Startbutton von Advance Steel die entsprechende AutoCAD Version zuweist. Ansonsten würde Advance Steel immer mit der zuletzt geöffneten AutoCAD Version starten.
Zuweisung der AutoCAD Version
Wählen Sie dazu das Startbutton mit der rechten Maustaste aus und klicken Sie auf Eigenschaften.
[file not found...]Es erscheint folgendes Fenster:
[file not found...]In der Zeile Ziel finden Sie folgenden Eintrag: "C:\Program Files\Graitec\Advance Steel\2014\Steel\Bin\AdvanceSteelLauncher10x64.exe" /T "C:\ProgramData\Graitec\Advance Steel\2014\Shared\Support\Templates\ASTemplate.dwt"
Geben Sie nun am Ende ein Leerzeichen und folgenden Eintrag ein: /AcadVer R…
Anstelle der drei Punkte tragen Sie nun die richtige Versionskennung ein:
AutoCAD 2010: R18.0
AutoCAD 2011: R18.1
AutoCAD 2012: R18.2
AutoCAD 2013: R19.0\ACAD-B001:407
AutoCAD 2014: R19.1\ACAD-D001:407
AutoCAD Architecture 2010: R18.0
AutoCAD Architecture 2011: R18.1
AutoCAD Architecture 2012: R18.2
AutoCAD Architecture 2013: R19.0\ACAD-B004:407
AutoCAD Architecture 2014: R19.1\ACAD-D004:407
Empfehlenswert ist auch, unter Allgemein den Namen der Verknüpfung zu ändern, damit die Verknüpfung bei einem Update nicht überschrieben wird.
Klicken Sie dann auf Übernehmen und OK, dann sollte Advance immer mit der ausgewählten AutoCAD Version starten.
Zu beachten wäre noch, dass ab AutoCAD 2013 die Zuweisung nur mit der genauen Information der AutoCAD Version funktioniert. Diese finden Sie leider nur in der Registry.
Gehen Sie dazu auf Windows Start und geben Sie dort im Suchfeld „regedit“ ein und drücken Sie Enter.
Es öffnet sich der Registrierungseditor:
[file not found...]Unter dem Registrierungsschlüssel z.B. für AutoCAD 2014: Computer\HKKEY_CURRENT_USER\Software\Autodesk\AutoCAD\R19.1 im Eintrag „CurVer“
finden Sie die genaue Information der AutoCAD Version.
Weitere Optionen:
In AutoCAD ist es möglich, eigene Profile und Arbeitsbereiche für Advance Steel zu definieren. Dies kann von Vorteil sein, wenn man noch andere Anwendungen auf AutoCAD verwendet wie z.B. AutoCAD Mechanical. Um diese Profile und Anwendungsbereiche über das Startbutton von Advance Steel gleich mit auszuwählen, geht man folgendermaßen vor:
Profile:
Als Erstes sollte das Profil im reinen AutoCAD ohne Advance Steel über die Optionen erzeugt werden (Vorgehensweise entsprechend AutoCAD Hilfe).
[file not found...]Dazu kann man unterschiedliche Schreibweisen wählen, entweder mit << >> wie z.B. <
> oder ohne wie z.B. AutoCAD. Je nach dem ändert sich dann auch die Schreibweise in der Zeile Ziel im Startbutton. Die Eintragung in der Zeile Ziel sollte an der rot hervorgehobenen Stelle erfolgen:
"C:\Program Files\Graitec\Advance Steel\2014\Steel\Bin\AdvanceSteelLauncher10x64.exe"I/T "C:\ProgramData\Graitec\Advance Steel\2014\Shared\Support\Templates\ASTemplate.dwt" /AcadVer R19.1\ACAD-D001:407
Mit << >>: "C:\Program Files\Graitec\Advance Steel\2014\Steel\Bin\AdvanceSteelLauncher10x64.exe" /p <
> /T "C:\ProgramData\Graitec\Advance Steel\2014\Shared\Support\Templates\ASTemplate.dwt" /AcadVer R19.1\ACAD-D001:407Ohne << >>: "C:\Program Files\Graitec\Advance Steel\2014\Steel\Bin\AdvanceSteelLauncher10x64.exe" /p "Advance" /T "C:\ProgramData\Graitec\Advance Steel\2014\Shared\Support\Templates\ASTemplate.dwt" /AcadVer R19.1\ACAD-D001:407
Arbeitsbereiche (Workspace):
Als Erstes sollte das Profil im Advance Steel über die Optionen erzeugt werden (Vorgehensweise entsprechend AutoCAD Hilfe).
[file not found...]Die Eintragung erfolgt dann am Ende der Zeile Ziel:
"C:\Program Files\Graitec\Advance Steel\2014\Steel\Bin\AdvanceSteelLauncher10x64.exe" /p "Advance" /T "C:\ProgramData\Graitec\Advance Steel\2014\Shared\Support\Templates\ASTemplate.dwt" /AcadVer R19.1\ACAD-D001:407 /w "AS2014"
Mit freundlichen Grüßen / Best regards
Elias Theuring
-
Sehr geehrte Damen und Herren,<br/>nun habe ich die Lizenz für Advance CAD von Graitec <br/>erhalten, jedoch fehlt mir eine Lizenz für Autocar Advance <br/>Steel.<br/>Ich hatte anscheinend übersehen auf das Mail von Autodesk <br/>zu antworten, habe aber
Hallo Herr Sokolowski,
wie gesagt, unser Vertrieb wird sich mit Ihnen in Verbindung setzen.
MfG
Elias Theuring
-
Sehr geehrte Damen und Herren,<br/>nun habe ich die Lizenz für Advance CAD von Graitec <br/>erhalten, jedoch fehlt mir eine Lizenz für Autocar Advance <br/>Steel.<br/>Ich hatte anscheinend übersehen auf das Mail von Autodesk <br/>zu antworten, habe aber
Hallo Herr Sokolowski,
unser Graitec Vertrieb wird sich mit Ihnen in Verbindung setzen. Eigentlich sollten Sie von uns eine E-Mail erhalten haben. Evtl. haben Sie diese aus Versehen gelöscht oder sie ist in einem Spam- bzw. Junk Ordner gelandet.
MfG
Elias Theuring
-
Sehr geehrte Damen und Herren,<br/>nun habe ich die Lizenz für Advance CAD von Graitec <br/>erhalten, jedoch fehlt mir eine Lizenz für Autocar Advance <br/>Steel.<br/>Ich hatte anscheinend übersehen auf das Mail von Autodesk <br/>zu antworten, habe aber
Hallo Herr Schwarzl,
auf unserer Homepage im Bereich Graitec Advantage finden Sie bei den Downloads unter Versionen das Online Setup für Advance 2015.
MfG
Elias Theuring